- #ICOM CLONING SOFTWARE CS P7 FOR ICOM IC E7 HOW TO#
- #ICOM CLONING SOFTWARE CS P7 FOR ICOM IC E7 MANUAL#
- #ICOM CLONING SOFTWARE CS P7 FOR ICOM IC E7 CODE#
With the temperature between –20˚C to +20˚C (–4˚F to The battery may heat up or rupture if charged out of the +68˚F).īATTERY CHARGING ■ Battery installation eReplace the battery cover to the transceiver. Shows half-capacity, then keep it safely in a cool dry place Icom recommends charging the battery at +20˚C (+68˚F). Use and charge only specified Icom battery explosion. R DANGER! NEVER incinerate used battery pack since in- ternal battery gas may cause it to rupture, or may cause an. 16)!2 TONE INDICATORS ➥ “LOW” appears when the low output power is selected. Appears when the RF attenuator is in use. 43)!1 ATTENUATOR INDICATOR (p.ġ5) Appears when priority watch is in use. PANEL DESCRIPTION r PRIORITY WATCH INDICATOR (p. PANEL DESCRIPTION ■ Function display WFMAM - DUP T SQL DTCS VOL PRIO P SKIP q FREQUENCY READOUT e BATTERY INDICATOR ➥ No indicator appears when the installed battery pack Displays a variety of information, such as an operating fre- quency, set mode contents, memory names. 12) ➥ Push to select the operating frequency band. MODE SCAN LOCK ➥ Push momentarily to select the call channel. PANEL DESCRIPTION y KEY CALL (!0 BAND.TUNING STEP.LOCK KEY BAND (. SCAN ➥ Push briefly, then push and hold to transmit a 1750 Hz Microphone tone burst. 16) ➥ Push and hold to transmit, release to receive. † An optional HM-153P can be connected to PIN MICROPHONE the IC-E7 directly (without the OPC-782). Rotate DIAL to change the scanning direction. Push V/M ( ) to select the VFO mode for full, band. QUICK REFERENCE GUIDE D D Starting scan 3. The pro- Push and hold V/M ( ) for 1 sec. Writing a memory channel 50 channels of memories in 25 pairs are used to specify scanning ranges for programmed scan operation. QUICK REFERENCE GUIDE ■ Programmed scan operation 3. Writing a memory channel 200 auto write channels and 50 scan edges) for storing often Push and hold V/M ( ) for 1 sec. QUICK REFERENCE GUIDE ■ Memory programming The IC-E7 has a total of 1250 memory channels (including 3. Repeater tone qWhile pushing and holding DIAL qWhile pushing and holding DIAL FUNC, push and hold SQL FUNC, push and hold SQL ) for 1 sec. QUICK REFERENCE GUIDE ■ Repeater operation 1.
#ICOM CLONING SOFTWARE CS P7 FOR ICOM IC E7 HOW TO#
Pages 11 and 17 will instruct you on how to set the push FUNC, CALL. Operating mode selection The tuning dial will allow you to dial in the frequency you want ➥ While pushing and holding to use. We would like to take you through a ➥ Push Y Y /Z Z to set the desired audio level. Adjusting audio level Now that you have your IC-E7 ready, you are probably ex- cited to get on the air. WInsert the adapter plug into 1216V DC INPUT of the BC- Transceiver to 1216V DC INPUT jack BATTERY CHARGER eInstall the BP-243.
QUICK REFERENCE GUIDE D Charging the battery D Charging description qPlug the AC adapter into an AC outlet or the optional CP- 21LR into a cigarette lighter socket. Insert the supplied antenna into the wInstall the BP-243 (Li-Ion battery pack). QUICK REFERENCE GUIDE ■ Preparation D Battery installation D D Antenna qRemove the battery cover from the transceiver.
#ICOM CLONING SOFTWARE CS P7 FOR ICOM IC E7 CODE#
18 ■ Tone squelch frequency/DTCS code setting.46 ■. 16 9 TONE SQUELCH AND POCKET BEEP.45–48 ■ Dial select step.17 ■ Tone/DTCS squelch operation.45 ■ Lock function. ■ Transmitting.16 ■ Priority watch operation.43 ■ Transmit power selection. I EXPLICIT DEFINITIONS.i PRECAUTION.ii SUPPLIED ACCESSORIES.iii TABLE OF CONTENTS.iii QUICK REFERENCE GUIDE.I–VIII ■ Preparation.I ■ Your first contact.III ■. SUPPLIED ACCESSORIES TABLE OF CONTENTS FOREWORD. If you have any questions re- NEVER operate or touch the transceiver with wet hands. Caution should be observed when operating this device. This device emits The transceiver may be damaged. PRECAUTION RWARNING RF EXPOSURE! NEVER expose the transceiver to rain, snow or any liquids. For making your IC-E7 your radio of choice, and hope you agree with Icom’s philosophy of “technology first.” Many hours of re- search and development went into the design of your IC-E7. We want to take a couple of moments of your time to thank you the IC-E7. Operation is sub- ject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Concluded that the icom-p7 is not overcome. With my lips touching the ic-e7 for making a 'normal.
#ICOM CLONING SOFTWARE CS P7 FOR ICOM IC E7 MANUAL#
INSTRUCTION MANUAL VHF/UHF DUAL BAND FM TRANSCEIVER This device complies with Part 15 of the FCC rules.